{"id":1296,"date":"2016-07-28T18:33:19","date_gmt":"2016-07-28T23:33:19","guid":{"rendered":"http:\/\/tenonandspline.com\/?p=1296"},"modified":"2016-08-31T08:36:47","modified_gmt":"2016-08-31T13:36:47","slug":"charvel-surfcaster-starting-the-build","status":"publish","type":"post","link":"https:\/\/tenonandspline.com\/blog\/archives\/1296","title":{"rendered":"Make-A-Wish Charvel Surfcaster: Starting the Build"},"content":{"rendered":"
This entry is part 1 of 7 in the series Make-A-Wish Surfcaster<\/a><\/div>
\"The

My first charity guitar – theLCA SG Jr.<\/p><\/div>\n

\"Charity

Charity guitar #2 from last year’s raffle.<\/p><\/div>\n

\"The

The first parts order arrives!<\/p><\/div>\n

\"Template

Template on Ash body blank<\/p><\/div>\n

\"Gluing

Gluing up the body blank<\/p><\/div>\n

\"Tear-out

Tear-out section following CA glue and sawdust treatment<\/p><\/div>\n

In 2014 I had the idea that I could build an electric guitar (my first) and raffle it off for charity through my company’s holiday party band, the LCA. This resulted in the LCA SG Jr. guitar <\/a>which raised over $2,100 for Make-A-Wish Illinois<\/a>. Last year this was repeated with a Lospennato-inspired “Radio star”<\/a> clone, though I entirely failed to blog about it. That guitar, thanks to a very generous\u00a0company match<\/a>, contributed over $5,000 to Make-A-Wish. These guitars were nice, but I really want something special <\/em>for\u00a0electric\u00a0guitar – and charity raffle – #3.<\/p>\n

On a recent trip to a local bookstore, I came across Tony Bacon’s The Ultimate Guitar Book<\/a>\u00a0and decided it would look nice in my music room<\/a>. There were some great photos of classic and modern guitars that made for a cool coffee table book. On a whim, I packed this book up with my stuff for a recent week-long camping vacation…and read it.<\/p>\n

That’s where I first set eyes on the beautiful Charvel Surfcaster<\/a>. Built in the 90’s this semi-solid electric featured a retro look with large pearloid pickguard and shiny, sleek, lipstick-style single coil pickups. I knew instantly this would be the 2016 charity guitar.<\/p>\n

The Drawing<\/strong><\/p>\n

I initially drafted the surfcaster\u00a0shape on the computer using CorelDraw and a pretty good, large, top view photo from the ‘net. This came out looking great, but I thought it seemed a little undersized.\u00a0I had carefully scaled the photo up to a scale length of 25.5″ but the body wound up measuring only\u00a0a bit over 16″. Clearly my photo reference wasn’t a precise top view, resulting in a bit of a skew. So I did some further searching and found a nice drafting of this guitar<\/a>, including dimensions. The drawing was a bit too small to simply print out – it was far too pixelated when blown up\u00a0to use at full size.\u00a0I was, however,\u00a0able to scale it up in CorelDraw and then adjust and tweak\u00a0my original drawing to match by overlaying it on top.<\/p>\n

I now had a full-size vector drawing of the guitar, including the sound hole, pickguard, and electronics cavities. (Download the PDF here<\/a>).<\/p>\n

Back from Camp, Down to Work<\/strong><\/p>\n

I returned from camp to find a box from StewMac.com waiting.\u00a0This first parts order included\u00a018:1 Grover tuners I’d picked out\u00a0and a couple different bridges to try.\u00a0I’d decided against installing a tremolo, but\u00a0am\u00a0planning on\u00a0through-body\u00a0stringing. I also ordered a couple other top-mount bridges just in case I change my mind.<\/p>\n

First step for any new\u00a0guitar project\u00a0is making templates. The base body template was cut from 1\/4″ MDF. I also cut the resonating cavity out of the template. I figured I after pattern-routing the body I could route this cavity before removing the template.<\/p>\n

With this first template, crafting the body was fairly simple. I had some 8\/4 Ash in stock for the base and my last (gulp!<\/em>) wide piece of birdseye Maple would be resawn and applied\u00a0as the top.<\/p>\n

The Ash blanks were jointed, glued, and drum sanded to thickness. I didn’t have an exact measurement for the body thickness of the original surfcasters.\u00a0They certainly look like fairly beefy guitars in the photos and there’d be quite a bit of weight removed from the body when I route out the resonating cavity. I figured they were likely somewhere between 1.75″ and so I’d probably go with around 1-7\/8″ to 1-15\/16″\u00a0 finished thickness. I surfaced the Ash blank down to just under 1.70″ and attached the template with double-stick tape and a couple screws. Since the top of the Ash would be hidden under the birdseye, the small screw holes could basically be anywhere and would ensure the template wouldn’t slip during routing.<\/p>\n

I cut the basic shape out on the bandsaw,\u00a0staying as\u00a0close to 1\/16″-1\/8″ from the attached\u00a0template as possible, being careful of course not to cut into it. Turning to my router table, I installed one of my longest\u00a0flushing bits and began carefully routing\u00a0the final shape. This is where I\u00a0ran into that very common and annoying snag\u00a0– as I rounded the lower bout\u00a0the Ash tore out pretty bad. This is end grain routing, where tear out is almost inevitable, but I had hoped I’d cut close enough to the final shape, and held the block firmly enough, to avoid it. I was wrong.\u00a0A better strategy here (next time) would have\u00a0been to route a portion of the full thickness at a time with the template\u00a0and bearing\u00a0initially at the bottom, and then cleaning up with the long\u00a0flushing bit.\u00a0The fix for this was to fill the gaps with some sawdust and CA glue and then sand<\/em> the rest of the body to the final dimension.<\/p>\n

Next up: finishing off the body and making the birdseye maple top…<\/p>\n","protected":false},"excerpt":{"rendered":"

This entry is part 1 of 7 in the series Make-A-Wish Surfcaster<\/a><\/div>

In 2014 I had the idea that I could build an electric guitar (my first) and raffle it off for charity through my company’s holiday party band, the LCA. This resulted in the LCA SG Jr. guitar which raised over $2,100 for Make-A-Wish Illinois. Last year this was repeated with a Lospennato-inspired “Radio star” clone, … Continue reading »<\/span><\/a><\/p>\n","protected":false},"author":180,"featured_media":0,"comment_status":"closed","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[131,167,3],"tags":[153,132,133,161],"series":[169],"_links":{"self":[{"href":"https:\/\/tenonandspline.com\/blog\/wp-json\/wp\/v2\/posts\/1296"}],"collection":[{"href":"https:\/\/tenonandspline.com\/blog\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/tenonandspline.com\/blog\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/tenonandspline.com\/blog\/wp-json\/wp\/v2\/users\/180"}],"replies":[{"embeddable":true,"href":"https:\/\/tenonandspline.com\/blog\/wp-json\/wp\/v2\/comments?post=1296"}],"version-history":[{"count":21,"href":"https:\/\/tenonandspline.com\/blog\/wp-json\/wp\/v2\/posts\/1296\/revisions"}],"predecessor-version":[{"id":1436,"href":"https:\/\/tenonandspline.com\/blog\/wp-json\/wp\/v2\/posts\/1296\/revisions\/1436"}],"wp:attachment":[{"href":"https:\/\/tenonandspline.com\/blog\/wp-json\/wp\/v2\/media?parent=1296"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/tenonandspline.com\/blog\/wp-json\/wp\/v2\/categories?post=1296"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/tenonandspline.com\/blog\/wp-json\/wp\/v2\/tags?post=1296"},{"taxonomy":"series","embeddable":true,"href":"https:\/\/tenonandspline.com\/blog\/wp-json\/wp\/v2\/series?post=1296"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}